1 May 2014
Table of Contents 1 Mystik Canopy/Island Image Guidelines 4 Mystik Pump Image Guidelines 6 Mystik Building Image Guidelines 7 Sign System: 6x6 8 Sign System: 5x5 9 Sign System: 5x10 9 Sign System: 4x8 10 12' Universal Pole Specifications 11 Mystik Material List
Mystik Canopy/Island Image Guidelines Primary Fascia Elevation Primary X-Form Mystik Red Wordmark Mystik Bronze Bollards Mystik Medium Red Secondary Fascia Elevation Island Curb Mystik Bronze Secondary X-Form 1 May 2014
Mystik Canopy/Island Image Guidelines Tools Required Utility Blade Marker or Pencil Pin or Needle Plastic Squeegee Sponge Rivet Brush Ruler or Tape Masking Tape Isopropyl Alcohol Soap and Water Paper Towels Industrial Heat Gun Surface Preparation 1. Surface must be above 50 o F and below 100 o F. Surface may be heated or cooled mechanically before application. 2. Lifted or loose edges must be trimmed and smooth prior to application. 3. Clean surface with soap and water. Rinse and dry. 4. Clean surface with isopropyl alcohol using lint-free paper towels. Red and X-Form Decals Application Step 1: Install Mystik red solid vinyl all around the canopy (provided in 8 sections). After applying the decals on the canopy, all canopy seams should be cut and tucked into the seam with the squeegee edge. Step 2: Determine whether the fascia is primary or secondary, based on visibility/order. Install the X-Forms on 1 primary and 1 secondary side. Make sure the X-forms meet and line up on the edge where the secondary and primary meet. Step 3: Install the Mystik wordmark from the right edge of the primary side and centered top to bottom. Distance of the wordmark from the right edge is determined by the canopy fascia height. Refer to illustration above and chart to the right. ***Mystik wordmark must not intrude into the X-Form 25 w x 40 h 25 w x 40 h 76.57 w 21 w 19.258 h 24.15 h OVERVIEW OF A FINISHED IMAGED CANOPY CANOPY VINYL LETTER DECAL SIZING Canopy Fascia Heights 0"-29" Mystik Vinyl Letter Size Custom - Please consult your CITGO Region Brand Manager Letter Spacing From Right Edge 30"-39" 24" 21" 40"-49" 33" 28" >50" Custom - Please consult your CITGO Region Brand Manager Custom - Please consult your CITGO Region Brand Manager Custom - Please consult your CITGO Region Brand Manager 2 May 2014
Mystik Canopy/Island Image Guidelines Application Instructions 1. Apply a masking tape hinge vertically at the center of the decal. (FIGURE 1) 2. Fold half of the decal hinge, peel off liner to tape hinge, cut liner along hinge and discard. (FIGURE 2) 3. Fold back holding decal off surface. Starting at center of tape hinge, squeegee decal using very firm, vertical overlapping strokes. Throughout application keep the unapplied portion of the decal off the surface, allowing it to touch only from squeegee pressure. (FIGURE 3) FIGURE 1 FIGURE 2 Panel Seam 4. While applying the decals on the canopy, ensure that all canopy seams are cut and tucked into the seam with squeegee edge. (FIGURE 4) 5. Remove masking tape hinge and the remaining liner. Repeat step 3. 6. Continue applying decals overlapping each one 1/8" to 3/16". Trim with razor blade if necessary. 7. Wipe with paper towel. (FIGURE 5) Finishing 1. Puncture decal in several places around rivet heads. Press out air with squeegee. 2. Use rivet brush and heat from an industrial heat gun to make the decal conform to the rivet head. (FIGURE 6) 3. Remove white paper premask by pulling it back onto itself. (FIGURE 7) 4. Eliminate air bubbles by puncturing decal at the edge of the bubble (not the center) with a pin or needle. 5. Press out the entrapped air starting at the opposite edge from the puncture. (FIGURE 8) 6. Re-squeegee all edges and overlaps. Reheat and use rivet brush to seal film over rivets. Panel Seam FIGURE 3 FIGURE 5 FIGURE 7 FIGURE 4 FIGURE 6 FIGURE 8 3 May 2014
Mystik Pump Image Guidelines Product Dispenser Decals - Refer to CITGO Decal Image Standards OVERVIEW OF FINISHED PUMP DISPENSER (1 HOSE) OVERVIEW OF FINISHED PUMP DISPENSER (3 HOSE) Remove existing graphics on the dispensers. Prep and clean surface prior to installation. The surface must be clean and smooth and free of any wax or silicone, oxidation or loose flaking paint. Surface and air temperature: Minimum of 50 o F Diesel pumps will be imaged with graphics pictured at right: (one size decal cut to fit) Valance decals are provided in 3 pieces. X-Forms are to be installed on the front face of the pump and sides will be solid red vinyl. You will have 2 pieces of graphics to wrap 1 valance. Trim any excess material. 8 Install the Mystik wordmark 2.5" away from the right edge of the front face of the valance and centered top and bottom. 6.5 Front of Valance (36 W) Side of Valance Wordmark Produced & Applied Separately From Right Front Edge of Valance 4 May 2014
Mystik Pump Image Guidelines Wordmark Produced & Applied Separately From Left and Top Edges 16 4.375 5 Dashed Line Indicates 42 W x 37.25 H Visual Area Pumpskirt Decal for Gas Pumps Only Remove existing graphics on the dispensers. Prep and clean surface prior to installation. The surface must be clean and smooth and free of any wax or silicone, oxidation or loose flaking paint. Pumpskirt decals are provided in 2 pieces. Install the graphics by lining up the bottom left edge of the pump. Wrap the entire door with the graphics, including the side returns on the door. Trim any excess material. Install the Mystik wordmark 2.5" away from the top and left side edge of the door. See photos on previous page for placement on a single hose versus a 3-hose dispenser. Refer to visual image above. Install all other pump graphics provided for the dispensers, including octane decals, federal warning decals and product ID decals. Remove pump toppers on the current dispensers. Risers must be clean and free of vinyl. Canopy support poles and island curbs painted Mystik Bronze. Island guard poles painted Mystik Medium Red. Sign cabinets and sign poles painted Mystik Black. 5 May 2014
Mystik Building Image Guidelines Note: Mystik image is required only if the building has any other brand image elements at the time of conversion. 36 H Fascia Mystik Red Stripe Decal Supplied in 8 Sections CIT MRD40 Credit Card Door Decal 1. Remove all existing graphics and clean area prior to installation. 2. Install Mystik red vinyl. These are provided in 8' sections. 3. Mystik logo is to be centered top to bottom and left to right on the front fascia. After applying the decals on the building fascia, all fascia seams should be cut and tucked into the seam with the squeegee edge. (See illustration below) Panel Seam Panel Seam Please contact your Region Brand Manager with any questions: Central Region Tedd Hupp: 832-486-1966 Email: thupp@citgo.com Central Region Eric Kolber: 832-486-5947 Email: ekolber@citgo.com Northeast Region Sue Pascarella: 832-486-5717 Email: spascar@citgo.com Southern Region Susan Edge: 832-486-1995 Email: dedge@citgo.com 6 May 2014
Sign System: 6x6 SIGN SPECIFICATIONS Amps: 7.0 Net Weight: 6 x 6 sign: 190 lbs. 6 x 6 sign: 190 lbs. Total Weight: 380 lbs. Area: 72 square feet Cabinet color: Mystik Black POLE & FOUNDATION SPECIFICATIONS Design Windload: 30 PSF/100 MPH Pole Supports: 8 x 6 x 3/16 W.T. x 24 tubes Baseplates: 1 1/4 x 9 x 15 Anchor Bolts: 1 x 42 Foundation: 2-6 Dia. x 7-3 Deep 6'-0" 6'-0" 6 x6 Mystik ID Sign REGULAR UNLEADED 6 x6 3 Product Price Sign 6'-0" MID GRADE UNLEADED 6x6 SIGN 72 15/16" PRICE SIGN FONT 3 PRODUCT D/F 1/16" 17 SUPER PREMIUM 11 1/2" 24'-0" 11 1/2" 5/8" 73 1/16" 17 Mystik Black Amps: 3.49 Watts: 380 Net Weight: 190 lbs. Area: 36 S.F. Lumens: 1050 P.S.F. (6) F72T12 H.O.C.W. Lamps (1) Electronic Ballast (3.49 amps) 73 6 x8 Steel Tube 7-3 Deep 30 Dia. Caisson (4) 1 Dia. x 42 long Anchor Bolts Each bolt has (2) nuts & (2) washers 3/4 Dia. Rigid Conduit (one caisson only) #4 Rebar Ties 12 O.C. (5) #5 Rebars, 6-3 long equally spaced around an 24 dia. circle Concrete Pier Foundations 100MPH (30psf) 79 3 x5 Reinforced Handhole Front Elevation 7 May 2014
Sign System: 5x5 SIGN SPECIFICATIONS Amps: 7.0 Net Weight: 5 x 5 sign: 145 lbs. 5 x 5 sign: 145 lbs. Total Weight: 290 lbs. Area: 50 square feet Cabinet color: Mystik Black POLE & FOUNDATION SPECIFICATIONS Design Windload: 30 PSF/100 MPH Pole Supports: 8 x 6 x 3/16 W.T. x 24 tubes Baseplates: 1 1/4 x 9 x 15 Anchor Bolts: 1 x 42 Foundation: 2-6 Dia. x 7-3 Deep 5-0 5-0 5 x5 Mystik ID Sign 5x5 SIGN 60 1/4" PRICE SIGN FONT 3 PRODUCT D/F 10 1/2" 5-0 REG UNLD MID UNLD 5 x5 3 Product Price Sign 3/8" 15" 24'-0" 15" SUPER PREM 61 10 1/2" Amps: 3.49 Watts: 340 Net Weight: 145 lbs. Area: 25 S.F. Lumens: 1296 P.S.F. (5) F60T12 H.O.C.W. Lamps (1) Electronic Ballast (3.49 amps) Mystik Black 60 1/4 6 x8 Steel Tube 7-3 Deep 30 Dia. Caisson (4) 1 Dia. x 42 long Anchor Bolts Each bolt has (2) nuts & (2) washers 3/4 Dia. Rigid Conduit (one caisson only) #4 Rebar Ties 12 O.C. (5) #5 Rebars, 6-3 long equally spaced around an 24 dia. circle Concrete Pier Foundations 100MPH (30psf) 66 1/4 3 x5 Reinforced Handhole Front Elevation 8 May 2014
Sign System: 5x10 SIGN SPECIFICATIONS Amps: 7.0 Net Weight: 280 lbs. Area: 50 square feet Watts: 680 Lumens: 1100 P.S.F. Cabinet color: Mystik Black PRICE SIGN FONT 3 PRODUCT D/F 10 1/2" 15" 5-0 10-0 REG UNLD MID UNLD SUPER PREM M-SS-5x10B BETWEEN POLE MOUNT 119 1/4" M-SS-5x10C CENTER POLE MOUNT 119" (10) F60T12 H.O.C.W. Lamps (2) Electronic Ballast (@ 3.49 amps) (2) Electronic Ballast (@ 3.49 amps) (5) F96T12 H.O.C.W. Lamps (2) F60T12 H.O.C.W. Lamps 8-0 SIGN SPECIFICATIONS Amps: 2.34 Net Weight: 180 lbs. Area: 32 square feet Watts: 420 Lumens: 1150 P.S.F. Cabinet color: Mystik Black PRICE SIGN FONT 3 PRODUCT D/F 3/4" 11 8 1/2" M-SS-4x8B BETWEEN POLE MOUNT 97 5/8" M-SS-4x8C CENTER POLE MOUNT 97 5/8" 50 1/4" 50 1/4" 61 3/8" 61" Sign System: 4x8 4-0 REG UNLD MID UNLD SUPER PREM (4) F96T12 H.O.C.W. Lamps (1) Electronic Ballast (2.34 amps) (4) F96T12 H.O.C.W. Lamps (1) Electronic Ballast (2.34 amps) 9 May 2014
12' Universal Pole Specifications: 5'x10' and 4'x8' Sign Systems Foundation Design Notes 1. Concrete shall have a minimum compressive strength of 3,000 PSI at 28 days. 2. Reinforcing bars shall be ASTM A615 grade 60 steel. 3. Concrete footings are designed using a soilbearing force of 250 lbs./sq. ft. per foot of depth lateral. If this soil condition does not exist, it is the Erector's responsibility to have a new base designed for the existing soil conditions by a Licensed Structural Engineer. 4. Anchor bolts are to be manufactured according to AASHTO specification M314-90 grade 55. 10 May 2014
Material List CANOPY MC100 MC101 MPXD40 MPXD50 MPXP40 MPXP50 MPXS40 MPXS50 PUMPS MQ305 MQ307 MPX203 24 Mystik Decal 33 Mystik Decal Red Canopy Overlay, 40 x 96 Decal Red Canopy Overlay, 50 x 96 Decal 40 Primary X-Form Decal Kit 50 Primary X-Form Decal Kit 40 Secondary X-Form Decal Kit 50 Secondary X-Form Decal Kit Valance, Decal Set 13 x 92 with Mystik Pump Skirt (1 side) 32 x52 Red Vinyl with Mystik Black Decal (1 side) 40 x96 Overlay Pump Nozzel Area Refer to Pump Image Standards, Section 3 in your CITGO Image Standards and Installation Guidelines binder, for appropriate federal labeling, Safety and information decals, environmental decals, pump number decals, product IDs and octane decals. SIGNS NM-SS-4X8, 3P NM-SS-4X8, 1P 4 x 8 Complete Sign System, ID, 3 Products, Regular, Mid, Super, Fonts, Pole Changer 4 x 8 Complete Sign System, ID, 1 Product, Regular, Fonts, Pole Changer NM-SS-5X10, 3P 5 x 10 Complete Sign System, ID, 3 Products, Regular, Mid, Super, Fonts, Pole Changer NM-SS-5X10, 1P 5 x10 Complete Sign System, ID, 1 Product, Regular, Fonts, Pole Changer NM-SS-5X5, 3P NM-SS-6X6, 3P PAINT BP9534BZ 5 x 5 Between the Poles, Complete Sign System, ID, 3 Products, Regular, Mid, Super, Fonts, Pole Changer 6 x 6 Between the Poles, Complete Sign System, ID, 3 Products, Regular, Mid, Super, Fonts, Pole Changer Bronze Gloss, Water-Base Enamel (Canopy Poles, Curbs) CC2312RED Medium Red Gloss, Water-Base Enamel (Bollards) CC2669 CITGO Black Gloss, Water-Base Enamel (Sign Poles) 11 May 2014
2014 CITGO Petroleum Corporation Mystik, as well as the Mystik logo, trade name and trade dress, and all related marks are registered trademarks of CITGO Petroleum Corporation. CITGO Petroleum Corporation does not own, operate or maintain the retail locations bearing the Mystik logo, trade name and trade dress. BD_140217_004 12 May 2014